How To Reset Tire Pressure Sensor Chevy Silverado 2008. A horn chirp will confirm that the sensor has been reset A horn chirp will confirm that the sensor has been reset
After the horn chirp has sounded, proceed as in step 4 for the next 3 sensors in the following order: After the horn chirp has sounded, repeat step.
2006 Chevrolet Silverado 1500 LT Call Us Today 402
All tires are at about 38 pounds but the light is remaining on. All you should need to do is check and set all tire pressures and make sure to check the spare also, after all tires are set with air you then drive a few blocks and the light should reset if the light does not reset then you will need to find out which wheel has a bad air pressure sensor, this is done with a tool that is put on the valve stem or a scan tool to see which tire is showing the wrong pressure,.
How To Reset Tire Pressure Sensor Chevy Silverado 2008
Chevy silverado (2008) type of tpms system:Click “set/reset” and a message saying “tire learning active” will pop up.Direct tpms, sensors are installed in the wheel;Does anyone know how to reset the tire pressure monitoring system on a 2008 silverado?
Ensure the flat of the valve, lines up with the flats of the snap in the enclosure.Hold it in intell the info comes on.Horn will chirp twice, dic displays tire learning active;I checked tire pressure and added a little air to each.
If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.In the window it will show all the things you can reset.Initiate the tire pressure monitor learn mode by simultaneously pressing and holding the “lock” and “unlock” buttons on the keyless entry remote until you hear a.Keep your tire pressure monitoring system operating properly with.
Lf, rf, rr and lr.Listen for a double horn chirp, indicating entry into the tpm learn mode.Low tire pressure light is on all tire pressure is.My light came on two days ago.
Now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.Place your relearn tool against the sidewall closest to the valve stem (where you fill and test your psi).Press and hold the “set/reset” button.Press and release either arrow button until the tire pressure screen is displayed, then press the set/clr button.
Push and hold trip reset stem to begin the sensor matching process;Push the bottom knob ( to turn the station).Push the trip odometer reset stem until tire pressure is displayed;Push trip reset again to confirm;
Relearning sensor position turn the ignition to the “on” position, but do not start the silverado.Repeat for the rf/rr/lr sensorsRepeat the process for the passenger side front tire, passenger side rear tire, and the driver side rear tire.Repeat the process for the passenger side front tire, passenger side rear tire, and the driver side rear tire.
Resetting the tire pressure sensor on your 2008 chevy silverado can be somewhat complicated, but will only take about 10 to 12 minutes of your time.Start from the driver side front tire, remove the valve cap, and then increasing or decreasing the tire’s air pressure until a horn chirp sounds.Start from the driver side front tire, remove the valve cap, and then increasing or decreasing the tire’s air pressure until a horn chirp sounds.Starting with the lf tire, use a properly formatted tpms scan tool to scan each sensor in the foll owing order:
The first thing you will need to do is go to the tire you want to start with, which is the front driver’s side tire.The horn will chirp, after the vehicle has received a signal from each sensor.This week, we will go over tpms diagnostics for the 2008 chevy silverado.Tighten the torx screw to 1.3 n.m (11.5 lb in).
Turn off the radio and turn the key to the on postion.Turn on the ignition, with the engine off.Use the tool to activate the left front sensor single horn sounds;Using the dic, press the vehicle information button until the relearn tire positions message displays.
Using the driver instrument cluster, click the “vehicle information” button and navigate to “relearn tire position”.