How To Mount A Tv Above A Fireplace Without Studs. A threaded extension column of the appropriate length will enable the screen to hang low enough so that viewers won’t get a stiff neck from looking up, yet not so low that heat from the natural gas fireplace is a concern. All you’ll need are some general work tools.
An anchor is one of the simplest ways to hang a tv on the wall without a stud. Another trendy way to have a tv above your fireplace is by recessing it back into an alcove.
101 Resources Stacked Stone Tile House Stacked Stone
Because of their width, wood studs are a better option for hiding the cables inside the wall. Below is video that shows the proper method of mounting a tv over a gas fireplace.
How To Mount A Tv Above A Fireplace Without Studs
I’d bet that tv is less than 50lbs (unless it’s plasma), and using a standard flush mount (even one that gives you a small degree of tilt) with toggle bolts / snaptoggles will be just fine.I’m nervous so i’d use three of them.If a stud does not fall dead center to where you want to hang your television, you will need to mount a piece of scrap plywood on two studs in order to create a solid surface for your hardware.If the location is the fireplace, you likely have a couple of options:
If there simply aren’t any studs where you want to mount the tv, then you need to use some sort of hollow wall anchor.If there simply aren’t any studs where you want to mount the tv, then you need to use some sort of hollow wall anchor.If you are using an articulating mount please drill into the metal stud.If you do not mount your tv into studs, you risk major problems from the tv falling off and getting destroyed to the tv ripping out chunks of your wall when it falls.
If you’re not mounting the tv to an arm, adding plywood / tearing out the drywall to reinforce the existing studs isn’t needed.If your wall has furring stripes, cables will probably be left outside.If you’re in great doubt, do a bit of math :In this case it was a stacked stone fireplace, which required commercial still toggles.
Just drill a hole accordingly, insert the sleeve, and slide in the anchor piece.Let it cure, then attach the tv mount to the ply.Locating studs is important for mount picking, as sometimes you will have to make a lateral shift to center the tv.Mark the lines on the stone that need to be cut.
Most mounts are sold with all the hardware you need to complete installation.Mounting a tv on drywall or plaster without attaching to a stud can be a very safe and reliable solution if you know the limits of the wall and the toggles.Mounting a tv on drywall or plaster without attaching to a stud can be a very safe and reliable solution if you know the limits of the wall and the toggles.Mounting plates are placed behind the tv and screwed into the wall using any of the anchor screws above.
Once you believe you have found studs simple repeat the above test:Only mount a tv above a fireplace if temperatures in that spot do not surpass 100 degrees fahrenheit.Pointing the tv toward the sofa is the only way to ensure picture quality with lcds.Studs should be 1.5 inches wide, so check that you can mark both sides of the side (to mount into the middle).
Take into consideration, together with these drywall anchors, the use of a metal or plywood mounting plate or brace.Tap in a small nail to verify structure behind the wall board.The base of your tv wall mount can then be screwed into the mounting plate.The fix for this, if you’re set on mounting above a fireplace, is a wall mount that pivots the tv downward.
The idea with a mounting plate is that it adds several more anchor points while creating a larger surface area to carry the weight of the mount and your tv.The only supporting structures are metal studs on the edges (55 apart) with only drywall between.The screen will hang over the fireplace, several inches off of the fireplace brick, suspended from a steel ceiling mount that is rated for 175lbs.The wall above the fireplace is projected outward and measures 55 in width.
Then i would glue the plywood into place against the drywall and bolt it into the stud.Then, determine what type of material you are mounting the tv on the wall to.They help to prevent the screws from falling out of the holes on the wall, or from destroying your wall.This guide is for when you are using a fixed or tilting mounting bracket.
This is a sleeker way to accommodate electronics above the fireplace, preferable for those looking for a clean, modern look.Treat the tv like an art:Using your stud finder, mark in pencil the placement of your studs.We never compromise the stacked stone by drilling directly into it.
Yes, a tv can be mounted above an electric fireplace safely.Yes, it is possible to mount a tv without studs.You can position mounting plates behind the tv and bolt them into the wall utilizing each of the anchor screws mentioned above.You can then decide where to mount your tv so it’s in the perfect location without risk of falling down or becoming dislodged.
You can then mount the base of your tv wall mount will then be mounted onto the mounting board.You can use mounting plates, toggle anchors, ceiling mounts, anchors and many other options available.You may also choose to make your nook whatever dimensions you please to accommodate more than a television, should clearances allow.You may need to tap many small holes to accomplish this without an adequate stud finder.
Your television should be attached to the same altitude as you want to hang some pieces of art with the same dimension above your house fireplace.