How To Backwash A Pool Filter Youtube. A backwashing filter has a mechanism of cleaning itself when clogging happens. A typical filter depends on the manual cleaning of the filter element during clogging.
Again, it’s better to work when the filter’s off. And then after the backwash, i waited for 10 minutes to rinse but it never flowed to rinsed.
As the filter becomes dirty and clogged, the pressure will begin to rise in the filter. Attach your pool hose to the backwash port on your sand filter.
How To Backwash A Pool Filter Youtube
Basically, this is how it is done with a de filter:Be ready to invest some time to backwash your filter successfully.Before turning your valve handle back to filter, make a stop at the rinse setting.Check the pool and/or spa autofill for proper operation:
Depending on the type of filter you have, you will need to position your valve in a certain way.Filter and backwash filter mode.First, turn off the filter system.Get a backwash hose and d.e powder.
How to backwash your pool filter.How to check your pool for leaks.However, when i went to backwash it, it took a very long time to prime to backwash (i have a pentair sand dollar filter).I guess i’ll have to buy a new hose from intex and splice it together as noted above.
I’ll probably replace the current splice and use the long hose.If there are no labels attached to the pump to indicate the backwash position, read the product documentation.If you have sand filters, you don’t have to buy the powder at all.It should only take between 3 to 5 minutes to backwash the pool filter.
It’ll be even simpler for you.Just follow the below steps to get backwashing:Last week we changed the sand in our doughboy sand filter.Manipulate the valve to the backwash position.
Manipulate valve back to run position.My victory was only momentary.Normally, i very quickly go from filter, then pump off, then valve to backwash, then pump on, and i get backwash flow within seconds.Now there is a fair sized stream of water coming from the backwash hose while on filter setting.
Once the water is clean and clear, turn the pump off again.Replace the sand in the filter every five to seven years.Routine pool maintenance includes backwashing the pool filter.Running your filter on rinse helps to reduce the chances of any sand blowing into the pool after backwashing.
Sand filter #1 turn off the filter systemSelect the “backwash” position on your multiport valve handle.Shut off the pump, set the multiport valve or slide valve handle to the backwash position, roll out the backwash hose and turn the pump on again.So where does it go?
Take note of the pool water level.Take your backwash hose and attach it to the pool’s filter.The autofill should keep the pool water level at the middle of the skimmer box opening.The d.e powder only applies if you have a diatomaceous earth filter.
The other end of the hose should be placed in an area that will not mind getting a large excess of water, such as an open field or a backyard.The sand filter should come with this so that people can hose clamp something to the backwash port.Then, connect the backwash hose to the filter’s backwash port.This reverses the flow of water in the filter which flushes the dirt out of the sand and discharges it.
This will be the hub of where the backwash really happens.Try to alternate between backwash and rinse.Turn off the pump and turn the backwash valve (plunger or multivalve) to the backwash setting.Turn the pool filter system on and allow it to rush out of the backwash port and through the backwash hose for two minutes or so until the water in the sight glass runs clear.
Turn the pump off and rotate the handle ccw until it clicks into the next deep slot.Turn the pump on and allow it to run for two minutes or until discharge water in the sight glass is clear.Turn your filter back on and run the rinse setting for 10 seconds.Turning off your pump before moving the filter settings, using a rinse after the backwash, and letting your sight glass tell you when the backwash process is complete are all great tips for new pool owners to follow.
Using a backwash filter results in high production since there is little disturbance during the filtration process compared to regular filters.When you backwash a pool filter, or when you vacuum a pool to waste, the water that is pumped from the pool does not return to the pool.When you backwash the pool water exits the pool and in general either goes directly into the sewer system or to somewhere in your yard, such as on a lawn, a flower bed, under trees or wherever you direct it by laying out a backwash hose.When your turn the pump back on, you should see bubbles coming out of the pool returns indicating that you are in the “filter” mode.
You are almost done backwashing.You must have a functional pressure gauge so you know when it is time to backwash the filter.